Brass Tip Socket Set Screws
Metric Size: M1.4-M52, Inch Size: 0# - 2"
Various Drive and Point Types
Various Surface Finishes
Other Material Grades are available
Please feel free to contact us for more details
www.deltastorage.com
The installation of your new toolbox will require two people, a tape measure and a ½ inch deep socket and ratchet with an extension.
Begin with the toolbox on the ground behind the vehicle. The lid latches should face away from the truck.
Open the lid, remove the tray and check for the following:
Installation instructions
Keys
Two adhesive mounting pads
Two “J” bolts
Two metal washers
Two plastic retaining washers
Two nuts
Read the instructions prior to beginning installation.
Lift the box and place about halfway across the truck bed.
Turning the box upside-down will make re-positioning easier.
Position the mounting pad to align with the inside edge of the side wall, and approximately four inches from the front bed wall.
Press down to ensure firm, even contact of the adhesive.
Repeat for the other side.
Roll the toolbox right side up onto the mounting pads. Test that there is sufficient clearance for the lid to open.
At the front of the box, use your tape measure to ensure the gap between the inner wall of the truck bed and the inner sidewall of the toolbox are the same on each side. The box is now centered.
Lift the toolbox lid.
Locate the center mounting slot.
Next, place the retaining washer onto the “J” bolt, about ½ inch from the top.
This will keep the bolt from dropping through the mounting slot.
Slightly raise the toolbox and insert the “J” bolt into the mounting slot with the hook facing the bed wall.
Turn the bolt 90 degrees, lower the toolbox and slide the “J” bolt toward the lip of the bed wall.
Rotate the “J” bolt back to its original position and pull up.
The “J” bolt should catch on the underside of the bed wall lip.
Push down on the retaining washer to hold in place and attach the flat washer and nut.
With a ½ inch deep socket, ratchet until snug. Do not yet fully tighten.
Repeat for the other side.
Double-check all measurements to ensure the box hasn’t moved off-center during installation. Readjust if needed.
Now, firmly tighten both “J” bolts.
Place the tray back inside the box.
Retain your keys and close the lid.
The installation is complete.
www.deltastorage.com
I Rail fastening and clamping products;
1. Clips and clamps: E series include:E1609,E1809,E1817,E2007,E2009,E2055 and W series include SKL1,SKL3,SKL12,SKL14,SKL75 and other clamps;
2. Square head screw spikes and hook spikes: Diameter 5/8,3/4,7/8,15/16,1¡±, length from 4¡± to 12¡±series spikes and Ss series include Ss5,Ss8,Ss23,Ss25,Ss36 spikes;
3. Clip Bolt and Track bolt: Clip bolts of the HS26, HS32 series, switch bolts, square head bolts, Insert Bolts and AREMA Track Bolt;
4. Insulators: Nylon insulators used for E Clips and Guide plates for SKL clips;
5. Dowels: Plastic and nylon dowels used for all kinds of screw spikes;
6. Shoulders: Assembly with all kinds of e Clips.
7. Insulating pad: Plastic, rubber and EVA pad Used for E clips and SKL clips;
8. Steel pad: Cast iron and forging steel pad used for E clips and SKL clips.
II Rail Jointing products:
1. Fish plate: America used 115RE, 132RE fish plates; Europe, Africa and Asia used UIC54, UIC60 fish plates, South America used TJ45, TJ57 fish plates and the UK used BS60, BS75 fish plates;
2. Fish bolts: Bolts used for the fish plates listed above;
3. Gauge rod: AREMA 1-1/4¡± and UIC, BS rail used gauge rods.
III High strength bolts and other non-standard fasteners:
1. Hex bolts£»with the diameter over M24 DIN,ASTM, BS Hex bolts, grade 4.6,4.8,5.6,5.8,6.8,8.8,10.9,12.9;
2. All kinds of nuts, standard parts, washers, Construction Industry bolts and precision parts.