professional factory provide ASTM A193 B7 All Threaded Stud Bolts to Belarus Manufacturers

A193 B7 Socket Head Cap Screws for Romania

Bolts For Structural Steel Connections

ISO 13918 Welding Studs to Australia

ISO 13918 Welding Studs to Austria

Stud Bolts Types

Xox Bolts Meaning

---

professional factory provide ASTM A193 B7 All Threaded Stud Bolts to Belarus Manufacturers Related Video:

WRITTEN PROCEDURE:

Tools/Supplies:

1 x Barnett Clutch Cable (I used PN# 102-40-10005)
1 x 13mm wrench
1 x 12mm wrench
2 x 10mm wrenches
1 x 10mm socket
1 x 4″ drive extension
1 x 1/4″ drive ratchet
1 x medium sized adjustable wrench
1 x pair of side cutters
2 x replacement nylon (zip) ties –medium sized preferably black

Removal:

1) Locate the radiator plastic shroud right side mounting bolt under the right foot peg – remove it – 10 mm socket/extension
2) Locate the clutch cable slack adjuster, follow the cable, it will be under the right side of the engine case, covered by a rubber boot
3) Slide the rubber boot off and thread the adjuster together increasing the slack in the cable, (may need 10/12mm wrenches)
4) Use side cutters to cut/remove ONLY the nylon ties, be careful about your old cable and the nylon tie holders, you will want to reuse these for mounting your new cable
5) Follow the cable towards the rear, locate the rear clutch cable mount & loosen the upper mounting nut (the only one you can access) with a 13mm wrench until it completely comes off the threaded barrel
6) Use adjustable wrench and fit it to the end of the clutch rod on the engine gently lift up on the wrench to rotate the clutch rod and release the cable end from the clutch rod bevel and groove
7) Lower the clutch cable casing threaded barrel out of its mount (you may have to pull a bit) then slide the clutch cable through the cut out in the mount.
8) At the clutch lever remove the clutch cable casing from its position in the clutch lever mount housing.
9) Swing the clutch cable housing toward the front of the bike, this should push the lever back a bit and allow the cable end to be removed from the bottom of the lever
10) Slide the cable carefully down through the cable cover and then completely down and out between you radiator and the frame, the plastic shroud should be easily pushed aside for this process.
11) Be careful to remember the cable routing for the return trip.

Installation:

1) On new clutch cable and make sure all of the adjusters and set to their zero point, providing you with the most cable slack possible, grease contact points
2) Carefully thread your new clutch cable from the bottom of the Scout back up though between the radiator and the frame, through the cable way to the clutch lever.
3) Insert the cable end into its fitted location in the lever, swing the housing around and into the fitted position in the clutch lever mount.
4) At the engine end of the clutch cable slide the cable through the rear clutch cable mount and push the threaded barrel into place, ignore the nut for now.
5) Use adjustable wrench to rotate clutch rod on the engine while inserting the cable end into the clutch rod cradle and groove
6) Thread the mounting nut onto the threaded barrel of the cable housing and snug
7) Adjust cable slack adjuster nut so there is limited free movement of the clutch lever and also so the clutch rod is not in an engaged or semi engaged position. Snug the clutch cable slack adjuster lock nut with 2 x10mm wrenches
8) Fasten two black nylon ties and thread them through the holders and loop them around the clutch cable and snug to hold the cable in place without damaging the casing or restricting the inner cable’s movement
9) Test ride bike – readjust if necessary

Thank you to Tombsmen on www.indianmotorcycles.net for the written procedure.

First see my other video about huawei e5573s unlock and downgrade which is somehow related to it , how to Downgrade firmware on E5573s and E8372h ..

—————————————————————————-

Procedure of Unlocking is simple and for all of these given below huawei model and have been tested successfully …

Huawei E8372h-153
Huawei E8372h-608
Huawei E5573s-320
Huawei E5573s-606
Huawei E3372h
Huawei B310s-927

step1:- you downgrade firmware to version# 21.xxx.99.xx.xx

step2:- you use my new Huawei Unlock calculator from here https://youtu.be/q1QpgUpbSzM

step3:- you upgrade firmware to anyone that is suitable to your modem .. and thats it , now can use any non carrier sim in your modem device

but if you are unable to follow the above mentioned 3 steps then it means you are either stuck on upgraded firmware or in anyway your modem device unable to Unlock easily thats why you use Emergency Bootloader method or injection method , thats why i made these videos . and also injection method can also be used if you stuck with modem device not responding or you think is near to death ..

————————————————
Note:-

Do not use my old calculator, it hangs and freezes, I’ve just uploaded a new calculator, and he immediately unlock with a single release button,no need to calculate 8-digit unlock code Nck Network. https://youtu.be/q1QpgUpbSzM

——————————————-

in this video i used original huawei usbloader thats why important info like imei# and serial# and webui dashboard , all are wiped out, but later we got successs by restoring back all of these imei# and serial# and dashboard webui , you can see all of these in the video ..
so my suggestion is to use usblsafe instead of usbloader.bin ,

——————————————————————————

you should watch below video on how to insert webui , zong webui for e8372h is already uploaded to firmware folder .
Unlock E5573s with Downgrade and how to insert any custom web ui in modem device.