Chuyên sản xuất: thanh U/thanh chống đa năng/TY REN/TY TREO/TY RĂNG/THANH REN/ TY TREO mạ kẽm M6, M8, M10, M12, M16 – (High quality Galvanized Thread Rod) 1m, 2m, 3m, đạt tiêu chuẩn JIS B 1051 – JAPAN & DIN 975 & DIN 976- Đức, Đai treo /Cùm treo, Đai treo 2 mảnh (Pipe hanger/Conduit Clamp), tắc kê đạn, Đai treo Omega, cùm omega, Cùm Ubolt, Cùm Ubolt lá (U Bolts) Gía đỡ cơ điện (M&E/Mechanical Fixings, Fasteners and Spring steel Supports) Cùm treo ống / Kẹp treo ty & ống / Kẹp treo ống thép luồn dây điện, ống PCCC/ HVAC (Steel conduit hanger/Pipe hanger/Clevis Hanger), Kẹp xà gồ/ Kẹp dầm thép (Beam Clamp/Suspending Clamp/C-Clamp), Thanh chống đa năng (Unistrut Channel/ Strut/ C-Channel/ Double Unistrut profile ), Đai ốc lò xo cho thanh chống đa năng (Long spring nut), Tay đỡ đơn (Cantilever Arm), U cùm ( U bolts), Tắc kê đạn (Drop In Anchor), Đai treo (bát treo) cho hệ thống điện nhẹ M&E / HVAC/PCCC /Điều hoà không khí cho toà nhà cao tầng và nhà máy sản xuất công nghiệp tại Việt Nam.
Mọi thông tin chi tiết về sản phẩm của Cát Vạn Lợi, xin quý khách hàng vui lòng liên hệ: 1900 5555 49
CÔNG TY TNHH THIẾT BỊ ĐIỆN CÔNG NGHIỆP CÁT VẠN LỢI
VPGD : 61 Đường số 7, KDC CityLand Center Hills, P. 7, Q. Gò Vấp, TPHCM
Tel: 08-35886496/ 22 46 46 99
Fax: 08-35886505
E-mail: baogia@catvanloi.com
Website: WWW.CATVANLOI.COM –
https://ongluondaydienvietnam.wordpress.com/
Youtube: WWW.CATVANLOI.COM
Facebook: WWW.CATVANLOI.COM
Phòng chăm sóc khách hàng: 0943353039 (Mr.Tâm)
BUILD SHEET
Engine
Boxerworks in Watkinsville, GA, completely rebuilt
New rings, cylinders honed
Custom ARP head studs
ARP 12-point stainless bolts throughout
Heads ported, polished, guides and seats reworked
Fitted with dual plug ignition system
Cast aluminum air cleaner block off cover
Mikuni 32mm Flat Slide Carbs with aluminum stacks
Dyna Electronic Ignition
Transmission
Reworked by Boxerworks for smoother shifting
Custom shift linkage by Bryan Heidt @FM
Polished rear cover
ARP 12-point stainless fasteners
Frame
Rear section cut off and Mono-Shock fitted
Custom Control mounts
New 1 1/8 “ 4130 Chromoly loop in the rear to mount the tail section and seat New 1 1/4” downtubes going from the seat area to the top of the swingarm mount
Front End
Brakes: Brembo from a 2012 Triumph Speed Triple with custom FM rotor adapter
Forks: 2012 Triumph Speed Triple
Triple Trees: Custom stem on 2012 Triumph Speed Triple
Handlebar: 2012 Triumph Speed Triple
Headlights: RetroFit Source LED with FM stainless mounts
Wheels and Tires
Front: Metzeler Lasertec 100/90-19 with 18” x 2” Triumph Tiger aluminum rim
Rear: Metzeler Lasertec 120/90-18 with 1” x 2.5” aluminum rim
Stainless spokes: Buchanan
Mono-Shock Setup
Swingarm: Stock lengthened 2” then custom fitting of Mono-Shock adapter with input from FOX Shox
Driveshaft then lengthened to fit. The rubber driveshaft boot flange had to be cut off and repositioned to get the higher angle to work properly
Shock: FOX AirShox
Brakes: stock rebuilt polished housing and custom hiem actuator rod
Custom stainless license plate mount by Bryan Heidt @FM
Exhaust
Stainless header pipes with crossover from aftermarket fitted with custom FM Magnaflow muffler designed and built by Bryan Heidt. Exhaust diameter 1.5”E
Bodywork
Stock Tank mounted 1.5” higher in the rear
Gas Cap: Aviation cap NOS
Tail section: custom .060 3003 H14 Aluminum by Fuller with a 50s Buick
Porthole trim piece turned into the bezel
LED tailight
Paint: Designed by Fuller then applied by JDK and Chastin Brand to mimic the Breitling Stunt Team colors
Seat: Yellow and Black vinyl by John Whitaker with FM Aluminum base
Wiring
Wes Hines wired @FM using American Autowire vintage braided wiring components
Electronic Ignition with Dyna Coils
Speedcell Lithium Battery