Chuyên sản xuất: ỐNG RUỘT GÀ LÕI THÉP BỌC NHỰA DÀY/TY REN/TY TREO/TY RĂNG/THANH REN/ TY TREO mạ kẽm M6, M8, M10, M12, M16 – (High quality Galvanized Thread Rod) 1m, 2m, 3m, đạt tiêu chuẩn JIS B 1051 – JAPAN & DIN 975 & DIN 976- Đức, Đai treo /Cùm treo, Đai treo 2 mảnh (Pipe hanger/Conduit Clamp), tắc kê đạn, Đai treo Omega, cùm omega, Cùm Ubolt, Cùm Ubolt lá (U Bolts) Gía đỡ cơ điện (M&E/Mechanical Fixings, Fasteners and Spring steel Supports) Cùm treo ống / Kẹp treo ty & ống / Kẹp treo ống thép luồn dây điện, ống PCCC/ HVAC (Steel conduit hanger/Pipe hanger/Clevis Hanger), Kẹp xà gồ/ Kẹp dầm thép (Beam Clamp/Suspending Clamp/C-Clamp), Thanh chống đa năng (Unistrut Channel/ Strut/ C-Channel/ Double Unistrut profile ), Đai ốc lò xo cho thanh chống đa năng (Long spring nut), Tay đỡ đơn (Cantilever Arm), U cùm ( U bolts), Tắc kê đạn (Drop In Anchor), Đai treo (bát treo) cho hệ thống điện nhẹ M&E / HVAC/PCCC /Điều hoà không khí cho toà nhà cao tầng và nhà máy sản xuất công nghiệp tại Việt Nam.
Mọi thông tin chi tiết về sản phẩm của Cát Vạn Lợi, xin quý khách hàng vui lòng liên hệ: 1900 5555 49
CÔNG TY TNHH THIẾT BỊ ĐIỆN CÔNG NGHIỆP CÁT VẠN LỢI
VPGD : 61 Đường số 7, KDC CityLand Center Hills, P. 7, Q. Gò Vấp, TPHCM
Tel: 08-35886496/ 22 46 46 99
Fax: 08-35886505
E-mail: baogia@catvanloi.com
Website: WWW.CATVANLOI.COM –
https://ongluondaydienvietnam.wordpress.com/
Phòng chăm sóc khách hàng: 0943353039 (Mr.Tâm)
More tips on removing the screw below!
See the full guide here – https://iadrenalin.com.au/iphone-4-screen-replacement-or-repair/
Or grab the screw chart to help you remember where to put all the screws here – https://iadrenalin.com.au/diy/iphone-4-screw-chart/
If you’re repairing your iPhone you have about a 20% chance of shredding/stripping a screw at some point! Some of these are easy to get out but not always – check out these 2 easy ways that fix most issues up!
If the screwdrivers on that angle didn’t work then you can try scratching a notch into the screw with a small flat head screwdriver. This can give you some more tracking then repeat the above process. Otherwise try the drill! Just grab a small drill big and dill 2/3 of the cap of one of them. This will allow you to use a normal screwdriver to turn the whole head by twisting in the grove (hope that makes sense!)
You could also try this great tip from damon691104:
“Another way is to dab a little super glue on the screw and stick the pentalobe screwdriver inside the screw and allow that to dry. Then the glue will hold everything together making it much easier to turn the screw. You have to turn slowly at first so not to break the adhesion since its only a small amount of glue”.
Also this tip from Sophie Galbraith
“I really recommend tweezers! I couldn’t get mine out the bottom of t phone at all, but found after trying all the things listed here, getting tweezers around the slightly raised screw was the only way to get it out!”
If you’re trying to repair your iPhone 4 and are after an exhaustive guide then check out our 40 min+ complete walkthrough! https://iadrenalin.com.au/iphone-4-screen-replacement-or-repair/