Metric Size Socket Set Screws
Thread Size: M1.4-M52
DIN913, DIN914, DIN915, DIN916
ISO4026, ISO4027, ISO4028, ISO4029
Various Drive and Point Types
Various Surface Finishes
Other Material Grades are available
Please feel free to contact us for more details
1. Close all vehicle doors.
2. Insert the key into the ignition.
3. Hold down the power UNLOCK button on the driver’s door panel-continue to hold
down until instructed to release in step 9.
4. Perform steps 5 through 8 in fairly rapid succession.
5. Turn the ignition switch to the ON position (as far as you can go without starting the
engine).
6. Turn the ignition switch to the OFF position.
7. Turn the ignition switch to the ON position.
8. Turn the ignition switch to the OFF position.
9. Release the power unlock button on the door panel. The vehicle will lock and unlock
the doors automatically.
10. Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until
the door locks and unlocks.
This step may take up to 30 seconds.
11. Repeat step 10 NOW for each additional transmitter (including any existing
transmitters).
12. Turn the ignition switch to the ON position in order to exit the transmitter programming
mode.
Watch the full episode: https://www.youtube.com/watch?v=ViTC2S4PL6o
Ask This Old House general contractor Tom Silva shows how to cut and fold, and then fix, a rigid box spring. (See below for a shopping list, tools, and steps.)
Click here to SUBSCRIBE to the official This Old House YouTube channel: https://www.youtube.com/subscription_center?add_user=thisoldhouse
Shopping List for How to Move a Box Spring Up a Narrow Staircase:
- Large canvas or plastic tarp
- 16-inch-long 2×4, used with hammer for pounding flat bent wires.
- 2 1/2-inch-long screws
- 1×3, to replace metal support bar
Tools List for How to Move a Box Spring Up a Narrow Staircase:
- Slotted screwdriver, to pry up staples
- Handsaw, for cutting the wood frame of the box spring
- Bungee cord, to hold closed the folded box spring
- Hammer, for straightening bent wires
- Cordless drill with 5/32-inch-diameter drill bit, to bore pilot holes
- Cordless impact driver, for driving screws
- Staple gun, to reattach fabric
Steps for How to Move a Box Spring Up a Narrow Staircase:
1. Lay a large tarp on the driveway, then place the box spring facedown on the tarp.
2. Use a narrow slotted screwdriver to pry up the staples that secure the fabric to the bottom of the box spring. Peel back the fabric to expose the wood frame.
3. Pry up and remove the metal support bar.
4. Fold down the fabric on each of the long sides of the box spring.[
5. Use a handsaw to cut through the 1×3 wood strapping on each side.
6. Fold the box spring in half, then secure it with a long bungee cord.
7. Carry the folded box spring up the stairs and into the bedroom.
8. Unhook the bungee cord and flatten out the box spring.
9. Use a hammer and a 2×4 block to straighten out any badly bent box-spring wires.
10. Drill 5/32-inch-diameter pilot holes at an angle through the strapping cut in Step 5.
11. Reattach the cut strapping with two 2 1/2-inch-long screws; repeat to secure the cut strapping on the opposite side.
12. Replace the metal support with a 1×3 cut to length. Screw the 1×3 to the wood frame of the box spring.
13. Staple the fabric back onto the underside of the box spring.
Follow This Old House and Ask This Old House:
Facebook: https://www.facebook.com/ThisOldHouse
Twitter: https://twitter.com/thisoldhouse
https://twitter.com/asktoh
Pinterest: https://www.pinterest.com/thisoldhouse/
G+: https://plus.google.com/+thisoldhouse/posts
Instagram: https://instagram.com/thisoldhouse
Tumblr: https://thisoldhouse.tumblr.com/