How to install a Wall Safe.
https://www.deansafe.com/wall-safes.html Mary shows up how to Install a hidden Wall Safe in a closet wall. we used a DOJ approved Wall Safe from VLine. Great way to hide a pistol or drugs from the kids. For this and other wall safes go to https://www.deansafe.com/wall-safes.html
Hi, my name is Mary, and I am with V-line Industries, and today we are going to show you how to install the V-line quick vault in the wall. Okay, the first thing we have to do is find out where our studs are. You also want to make sure there is no electrical, or plumbing behind your wall.
There are two ways to do that, we can use a studfinder, which you can get at any hardware store, and that just lines up, and when you have a stud, the lights light up. Or, if you do not want to buy a stud finder, and you do not have one you just tap on the wall, and you can hear the difference between where the stud is, and where it is not.
And once you locate your studs, you want to mark them and that is where we are going to cut our hole, in between those two studs. Okay, so we have our drywall knife, you can use other knives, other tools we chose the drywall knife, so basically, you take your knife, and just poke your hole in the wall. Once you get through, you are just going to cut your hole out.
We just cut a small hole, so that we can double check and make sure that we do not have any electrical or plumbing back here. We did find one little cable wire, so we took Our coat hanger apart, and slid that down in here, and just double checked that we are lined up with our stud here, and with our stud on this side, our little cable wire is not going to be a big deal, we are just going to push that out of the way, and we are already, now, to make our hole bigger, so we can slide our safe in.
We have our hole all cut, we are going to just clean up this edge a little bit, and we are going to be ready to put our safe in the wall. Okay, we have our hole all cut and now we are ready to put our vault in the wall. So, we just slide it in our hole, and then open it up. We have our felt sides off, and we are going to mark our holes, so we can do some starter holes in the studs There are two holes on each side. And slide it back out again, so we can start some starter holes in the wall.
There is a good little mark there to start drilling. Okay, so we have our holes all started, we are going to put our safe back in the wall, and we have got fastening lag bolts, included we are going to take these guys out, and washers and we just put those right through the holes we started and right through the safe. And we get our rachet and we are ready to go. What you want to do too, is to get all four started in there, you do not want to tighten one down then go and tighten the other one. You just get all four of them done and then you go back in and do that final tightening on all of them. Just get them snug tight, do not crank them down too hard.
Okay, we are all secure there. Now our next step. We are ready to put our shelf in. Now in the back wall of the safe, we have got these slits in the felt. So we are going to pull the felt apart right at the slit, And you can see behind the slit here, It is lined with little holes and that’s what our shelf screws into.
So you just pick the desired height that you want your shelf. You have got both sides here, so I have separated the felt here and found my two holes what I am going to do is set my shelf in place, you have to angle it up to get it in and then we are going to line up the hole through the bottom of the shelf and then it goes right into the hole in the back wall we have our shelf and we are going to just tighten our screws down little bit more. And check our door, perfect.
So we are all finished now, we have got our vault installed and the shelf is in place, so I am all ready to fill it up now. Clean up, it does make a little bit
Of a mess, ladies, so we are going to bring the vacuum in and get up the drywall dust. We had a little faux pas here, I was thinking, I wanted it higher, but I had our closet bracket in the way. So we will just touch that up with some paint, no, big deal. The other dry wall cuts are all hidden by our flange here. If you are going to put this in a room it is flush enough, you can hang a picture over it and completely hide it. It sticks out maybe 1/16 of an inch or so, your knob sticks out just a touch over the flange. You are all set. It is really easy to use, you just turn the knob, push in the buttons, for the code you set, we will go over that in just a minute. It is so fast and easy to use. Thanks again for watching, Mary
To see more cool safes go to https://www.deansafe.com
Please Subscribe!
https://www.youtube.com/subscription_center?add_user=deansafe
DeanSafe’s Channel https://www.youtube.com/user/DeanSafe
Website: https://www.deansafe.com/
Store locations: https://www.deansafe.com/store-locations.html
Here is the replacement to the TROYBUILT pressure washer that locked up on me just a few hours after buying it.
GET YOUR PRESSURE WASHER HERE
https://amzn.to/2lJLBKu
Generac 196cc OHV engine delivers maximum cleaning performance and reliability
Axial cam pump with easy-access hose connections alleviates kneeling on the ground to connect hoses
Ergonomic spray gun with cushion grip handle and easy-to-pull trigger reduces fatigue and extends use
Integrated 3/4 gallon tank provides convenient onboard storage for cleaning detergents
25′ PVC hose connects to the rear of the spray gun for maximum convenience
Includes 4 Quick-change nozzle tips: 0, 25, and 40 degree, and soap
–Power wash your deck, driveway, patio furniture and more with this powerful pressure washer from Generac. Long been known for their quality engines, this model is no exception, equipped with a powerful 196cc Generac OHV engine. Also included are four Quick-Click nozzle tips (0-degree Blast, 25-degree Clean, 40-degree Wash, Soap) and a 25 foot hose. Generac’s power washers are carefully engineered for longevity and ease of use, with well thought-out features not found on competitive models. Easy to maneuver, the welded frame is designed for durability, with a built-in step for easy starting and an integrated gun holster. The easily accessible high-performance axial cam pump provides maximum heat dissipation for extended life and the easy to pull trigger reduces fatigue. The pump is located well above the ground, eliminating the need to kneel down to make hose connections. Backed with a 2 year limited warranty. Founded in 1959, Generac has earned a reputation as the company home and business owners turn to when the power goes out. The first to engineer affordable home standby generators, along with the first engine developed specifically for the rigors of generator use, Generac now sells more home standby generators than all of our competitors combined. We have brought this same level of commitment and quality to our pressure washer products. Our customer research has led us to engineer our pressure washers from the ground up, to meet your specific demands. Generac manufactures the widest range of power products in the marketplace including portable, RV, residential, commercial and industrial generators. Generac also operates three large factories which employs thousands of workers in the American Midwest. Note: This model is not for sale in California/non-CARB compliant.