How to replace the shaft seal on a KM pump
00:13 Step1. Remove the bearing cap
00:23 Step2. Remove the grease
00:29 Step3. Remove the lock washer and the shaft nut
00:57 Step4. Remove the bearing housing
01:50 Step5. Remove the retainer ring
02:12 Step6. Remove the used shaft seal
02.29 Step7. Mount the new shaft seal
02:42 Step8. Clean the sealing surface carefully
02:50 Step9. Mount the carbon ring in the container ring
03:02 Step10. Clean the sealing surface of the carbon ring
03:07 Step11. Mount the retainer
03:34 Step12. Remove the rear cap and the bearing from the bearing housing
03:52 Step13. Mount the rear cap again loosely
03:59 Step14. Mount the bearing housing
04:45 Step15. Mount the bearing
05:09 Step16. Mount the shaft nut and the lock washer
05:25 Step17. Mount the bearing cap loosely
How to line up the rotor
05:38 Step1. Make sure that the four bolts in the front bearing cap are tighten
05:43 Step2. Place a precision clock on the shaft
05:58 Step3. Force the rotor back until it makes contact with the rear flow plate
Now the rotor has contact with the flow plate and cannot be turned by hand
06:24 Step4. Loosen the bearing cap again
06:43 Step5. Reset the clock (O)
06:59 Step6. Force the rotor forward until it makes contact with the front flow plate
07:13 Step7. Make sure that the rotor has contact with the front flow plate
07:18 Step8. Note the rotors total moving space
In the case 0.36 mm
07:41 Step9. Move the rotor back again and ensure the equal space in both ends of the rotor
In this case 0.36mm/2=0.18mm
08:12 Step10. Lock the bear bearing by tightening the flour bolts
The rotor is now centered and locked
08:31 Step11. Check that the rotor is running free
08:42 Step12. Grease the pump according to the manual
For more information please visit: https://www.samson-pumps.com
Chuyên sản xuất:KẸP TREO ỐNG D1/ TY REN/TY TREO/TY RĂNG/THANH REN/ TY TREO mạ kẽm M6, M8, M10, M12, M16 – (High quality Galvanized Thread Rod) 1m, 2m, 3m, đạt tiêu chuẩn JIS B 1051 – JAPAN & DIN 975 & DIN 976- Đức, Đai treo /Cùm treo, Đai treo 2 mảnh (Pipe hanger/Conduit Clamp), tắc kê đạn, Đai treo Omega, cùm omega, Cùm Ubolt, Cùm Ubolt lá (U Bolts) Gía đỡ cơ điện (M&E/Mechanical Fixings, Fasteners and Spring steel Supports) Cùm treo ống / Kẹp treo ty & ống / Kẹp treo ống thép luồn dây điện, ống PCCC/ HVAC (Steel conduit hanger/Pipe hanger/Clevis Hanger), Kẹp xà gồ/ Kẹp dầm thép (Beam Clamp/Suspending Clamp/C-Clamp), Thanh chống đa năng (Unistrut Channel/ Strut/ C-Channel/ Double Unistrut profile ), Đai ốc lò xo cho thanh chống đa năng (Long spring nut), Tay đỡ đơn (Cantilever Arm), U cùm ( U bolts), Tắc kê đạn (Drop In Anchor), Đai treo (bát treo) cho hệ thống điện nhẹ M&E / HVAC/PCCC /Điều hoà không khí cho toà nhà cao tầng và nhà máy sản xuất công nghiệp tại Việt Nam.
Mọi thông tin chi tiết về sản phẩm của Cát Vạn Lợi, xin quý khách hàng vui lòng liên hệ: 1900 5555 49
CÔNG TY TNHH THIẾT BỊ ĐIỆN CÔNG NGHIỆP CÁT VẠN LỢI
VPGD : 61 Đường số 7, KDC CityLand Center Hills, P. 7, Q. Gò Vấp, TPHCM
Tel: 08-35886496/ 22 46 46 99
Fax: 08-35886505
E-mail: baogia@catvanloi.com
Website: WWW.CATVANLOI.COM –
https://ongluondaydienvietnam.wordpress.com/
Youtube: WWW.CATVANLOI.COM
Facebook: WWW.CATVANLOI.COM
Phòng chăm sóc khách hàng: 0943353039 (Mr.Tâm)