Teach your child about circuits by using this fun and easy aluminum foil circuit activity.
Materials:
- Aluminum Foil
- Light bulb
- Batteries
- Paper
- Pencil
Instructions:
1) Design your circuit (Note: avoid crossing the circuit unless you plan to make it three dimensional – always a plus for the higher level students)
2) Make wires out of foil
3) Connect the light bulb to the foil (make sure to connect the foil in the correct areas. For incandescent light bulbs, connect one wire to the threads of the bulb and the other wire to the nub).
4) Attach batteries (for LED lights, the current has to flow in the correct direction. The shorter end of the LED is the negative side)
5) Light up! The light should light up.
Troubleshooting
1) Check the connections. A loose or broken wire might be the culprit. Make sure you’re connected to where you need to be.
2) Check the material. Does the battery work in something else? What about the light?
3) Check for short circuits. If a wire on one side is touching the wire on the other side, you could be short circuiting your circuit. This essentially means that the electricity has found an easier, faster way to go in a circuit and will no longer flow through the light.
4) Check the voltage. Do you have the necessary number of volts to light up the light? Too little will not turn the light on. Too much can cause an overload.
Safety
1) Make sure to have dry hands and a clean work environment.
2) DO NOT leave the circuit connected. When you are done, disconnect as this can overheat the batteries and present a fire hazard.
3) Use items that have a low voltage requirement (higher voltages present higher risks).
4) Avoid using too many volts as that can damage the electronic component and you!
5) Parental Supervision is advised.
Striplox Mini 120 Invisible Joiner
https://www.richelieu.com/QR/c/1198306
Striplox Mini 120 connectors enable a rapid assembly with a fully concealed joining and fastening solution to any piece of cabinetry, furniture, or design applications. The Striplox Mini 120 connectors produce a tight and strong joint either in a permanent or reversible configuration making them perfectly suited for commercial, domestic, and architectural furniture, kitchen — bathroom and wardrobe cabinetry, commercial fit-outs plus many more applications.
Integrating the Mini 120 connectors into your processes is easy. The installation incorporates existing manufacturing methods and delivers a fast assembly of components, panels or sections — either in the factory, in the home or in the most remote site locations.
Striplox Mini 120′s are suitable for numerous applications with the evenly distributed loading offering strength, durability and versatility. It offers the ultimate in fine line finishes — visually providing a concealed flush finish with no signs of fasteners or connectors being used like staples, screws, cam & dowels or cover caps.
The key advantage of the Striplox Mini 120 connectors is to deliver unmatched cost savings. Striplox Mini 120 connectors can be fitted in the factory ready to assemble by hand anywhere in the world at a fraction of usual assembly and installation costs. The unique design of the Striplox connectors offer many benefits and advantages on transportation savings, with the ability to flat pack with knock down components. Saving on assembly cost at installation, the components or cabinetry will firmly lock together without the need of tools, screws or fasteners saving time and labour.
You will also save on production costs and machining costs versus other substrate joiners with less positioning rebates and less components. Due to the unique load-spreading design, you will dramatically reduce the chance of substrate blow out commonly caused by over tightening conventional screws and fasteners.
ADVANTAGES AND BENEFITS
- No visible fixings — completely concealed joint
- Eliminates damage — install panels during final build
- Lower transportation cost — flat pack
- Lower labour costs with fast on site assembly
- Strength, Durability and Versatility
- Cabinetry or panels can be fitted permanently or removed with ease
- Joining will not interfere with substrate finish ie. Veneers, 2pac paint
- Can be used in substrates of 12mm thickness and upwards
APPLICATION
-Feature ceilings, walls, cabinetry, shelving
-Kitchen and cabinet hardware
-Commercial wall paneling and office partitioning
-Kitchen design
-Custom cabinets
-Modular entertainment builds
-Kitchen cabinet ideas
-Cabinet makers
-Locker systems assemblies
-Wood & timber joints
-Toilet/shower partitioning
-Wardrobe fit outs
-Framing of artwork/mirrors
-Furniture construction and interior fitting
-Shop fitting displays and signage
-Exhibition and trade events
-DIY garden shed and Patio
-RV and Marine fit outs
https://www.richelieu.com