WaxFREE Toilet Seal Kit 6000BP
Easiest way to install a toilet/fix leaks
No mess
Fits 3″ & 4″ drain pipes
Holds bolts upright for easy install
Replaces wax ring technologies
Rubber exterior and flexible thickness foam interior
WaxFREE Toilet Seal Kit 6000BP | https://bit.ly/1giIIJQ
This short video will give you a quick overview of what is required to complete your Korky WaxFREE seal installation. Included in your packaging are bolts, hex nuts, metal washers, and plastic washers. The rubber seal contains a thick foam ring and a thin foam ring. You will need a wrench, putty knife, and ruler. Please keep in mind, if your closet flange is cracked or damaged, it must be repaired before installing WaxFREE Seal. We do not recommend using sealants. First, shut off the water supply by turning it clockwise. Remove the tank lid and set it aside. Then flush the toilet to empty the water inside of the tank and sponge out the remaining water left in the tank & bowl. Disconnect the water supply line. Next, take off any toilet bowl caps and unscrew the nuts on each side of the toilet. Lift up on the toilet and remove it. If a wax seal was used on the previous install, you will have to clean the closet flange and bottom of the toilet by scraping off any wax. Helpful hint: Prior to installation, place the toilet on the flange to determine if the floor is even. Shims may be needed beneath the toilet to stabilize prior to installing the seal. Now remove the old closet bolts. Install new bolts by twisting bolt heads to secure. Slide the plastic washers down to the base of the bolts to hold in place.
Next, determine the closet flange height relative to the finished floor. If the closet flange is above the finished floor, use the ruler on the instructions to determine the height above the floor. If the flange is one half inch or above remove the thick foam ring. If the flange is below one half inch above the floor, remove the thin foam ring. Watch for: If flange is three eights of an inch to one half inch above floor, read cautionary note in step 6 of the instructions. If flange is even with or below, use the full seal, with both the thick and the thin foam ring. For extra deep flanges of three eights of an inch below the finished floor, also use the full seal, both thick and thin foam rings. If the flange is three eights of an inch or more below the finished floor, stack two seals on top of each other. Longer bolts may be needed. Now you can set the bowl in place, caution: toilet may be unstable initially. Install washers & hex nuts. Apply downward pressure to bowl while tightening hex nuts (alternate sides while tightening) Do not over tighten, bowl or closet flange may crack. If you need further assistance with the installation of the WaxFREE seal, call us at 1-800-528-3553.
Websit: https://www.jmtornillo.com
Ahora me gustaría presentarle las tuercas de mariposa
Los estándares son ASME B18.6X y DIN315
Los materiales son acero al carbono bajo, acero inoxidable y cobre.
Este es la tuerca de mariposa de acero inoxidable, este es de acero al carbono bajo Zincada amarilla.
La tuerca es disponible con el tornillo de mariposa en aplicación.
Tambien podemos fabricar tuercas hexagonales de mariposa especiales según sus muestras y dibujos
Shanghai Jian y Mei es un proveedor profesional de tuercas de estándar IFI y DIN, por ejemplo tuerca hexagonal pesada, tuerca hexagonal, tuerca cuadrada, tuerca flange, tuerca de bloqueo y Tuercas hexagonales de Acoplamiento etc.
Tenemos tamaños completos de M3 a M100, y 3/16” a 4”.
Los materiales pueden ser acero al carbono, acero de aleación, acero inoxidable y cobre.
Grados disponibles de tuercas son ASTM A563 grado A, grado C, grado DH, ASTM A194 Gr. 2, 2H, 7, 7M,8, 8M, SAE J995 Gr.2, 5,8; CL4, 5, 6, 8, 10, 12.
Los acabados son Zinc, Zinc amarillo, Óxido negro, galvanizado etc.
Tenemos más de ocho años de experiencia exportar tuercas de mariposa al mercado américo y poseemos buena fama, enfíen en nosotros que somos su proveedor fiable de fijación!
No dude en contactarnos en cualquier momento!
Shanghai Jian & Mei Industry and Trade Co., Ltd
Rm.27202, No.295 South Lingyan Road, Pudong,Shanghai,P.R.C, Code:200126
Tel: 0086-21-33328690-8058
Fax: 0086-21-68413263
English Web：www.jm-industry.com Websit: https://www.jmtornillo.com
Contact: Mrs.Xarella Huang
Email: Jminfo@jm-industry.com
Websit: https://www.jm-industry.com