Mots clés Ebay:
Brass Flat Washers GB97 M2 M3 M4 M5 M6 M8 M 10 M12 M14 M16 M18 M20
5pcs 3296W-501 500Ω Potentiometer / Multi-turn Precision Adjustable Resistor
Mots clés BangGood
TDA2030A 6-12V AC/DC Single Power Supply Audio Amplifier Board Module
10Pcs 100W Dummy Load RF RFP 1109 Microwave Resistor Power Watt 50Ω 0-3GHz
1/4 Inch 60mm Quick Release Hex Shank Screwdriver Bit Holder Magnetic Tool
Titanium Alloy Plate TC4/GR5 Titanium Plate 0.1×100×300mm
Safety Cut Proof Stab Resistant Stainless Steel Metal Mesh Butcher Gloves
JAKEMY JM-T8-11 Metal Grabber Beads Holder Diamond Pick-up Tools Repair Tools
6pcs 1/8-3/8 Inch HSS Combination Drill Tap Bit Set 1/4 Inch Hex Shank Deburr Countersink Bits
20Pcs RGB LED Diode 8mm Red/Green/Blue 4 Pin Light Emitting Diode
10Pcs 33UH 3A Toroidal Wound Inductor Nude Inductance Magnetic Inductance
10Pcs 330UH 3A Toroid Core Inductor Wire Wind Wound
200 Pcs 2.54mm Female Pin Long Dupont Head Reed Connector
100pcs 4P Dupont Jumper Connector Female Pin Wire 2.54mm Pitch
Cutting Plotter Vinyl Blade Holder with 15pcs 30 45 60 Degree Cutter Blade
290mm Flexible Shaft Bit Extention Screwdriver Drill Bit Holder Connect Link for Electronic Drill
100Pcs M4 5mm 304 Stainless Steel Socket Set Screws Hexagon Headless Screws
Diamond USB 2.0 Hi-Speed Micro SD SDHC TF Card Reader Support 32GB
Mini Micro SD TF 4GB Capacity Storage Memory Card for Car GPS Camera Mobile
Visitez mon site : https://www.Cyrob.org
DIY Home Gym Adjustable Pulley Cable Machine Build Log
Part 1 of 4 – Material Prep and Beginning Fabrication
Here’s a video log of how I built my own adjustable cable machine for my home gym. These are widely available online but I couldn’t find the one for me:
- Very expensive – £475 was the cheapest retail machine I could find with a rotating and height adjustable pulley.
- Size – You’ll see in the video that my home gym is not the biggest! All of the retail machines I found we’re totally floor standing and as such had large footprints to prevent them from tipping over. They would’ve taken up far too much space in my gym.
- Capacity – All the adjustable retail units that I could find used weight stacks and the cheapest maxed out at around 70KG which is fine for most exercises but could easily be exceeded for lat work and there didn’t seem to be any way to increase the maximum weight capacity.
My design uses 1″ bars to hold the weights so it can take standard home gym weight plates which you’ve probably already got and can be bought for next to nothing on ebay. As such it also has finer increments for weight adjustments which make it ideal for light weight rehab work.
I’d like others to have a go at building one of these (or two for a crossover!) for their own home gyms. I had intended for the videos to be a full tutorial for anyone to have a go but realistically I think a maker would need to have some basic/intermediate DIY/fabrication experience, as although I’ve made sure to include all of the important steps, I can’t possibly cover 100%. Also, for the significant cost savings to be viable, you’d need to already have a well stocked set of tools as you see me use in the video. That being said, I would invite anyone to give it a go!
My design DWG file and a PDF print are available through the below link:
https://www.dropbox.com/s/3rymtpe1svan1mt/Cable%20Machine.zip?dl=0
The PDF is intended as an overview only. If you’re going to build this then you will need to use the DWG file so you can take precise measurements and prints as and when you need them throughout the build. If you don’t have AutoCAD to view the file then you can download TrueView for free from the AutoDesk website which will let you measure and print as needed.
Basic Materials List:
40x40x2mm Mild steel welded box section for the main frame
50x50x2mm Mild steel welded box section for the weight plate mount and pulley mount
3mm Thick mild steel sheet for the base and all other plate pieces you see
1″ 14AWG Mild steel tube for the weight plates
M10 Part-threaded bolts, nuts, washers, rod etc
Steel sleeves, M10 internal, 15mm external
95mm Pulleys, M10 hole. Pack of 10 from Ebay Hong Kong seller
Plastic coated wire rope, 5mm overall diameter
8mm detent pin to secure the pulley assembly to its various heights on the frame
Split pins to secure the pulley assembly hinge pin
5mm Wire rope clamps and carabiner
40mmx40mm Box section plastic end caps
2mm Plastic sheet to sleeve the weight and pulley assemblies
Etch primer and gloss black top coat (approx 800ml of each)
4mm Thick mild steel spacer washers used to space pulleys from the frame according to the designs
With the exception of the main steel order, all other parts were from ebay.
Total material cost £196.92
I’ll provide more details on all of the above if needed.