Subscribe to our channel for the latest training videos, climbing tutorials and more! In this video we review falling considerations for the lead climber in sport climbing.
Sport climbing presents a unique opportunity for the climber to experience, practice and learn how to fall in a somewhat controlled environment. Bolts may be stronger than some gear placements, and many sport climbs are steep enough that the climber will fall into mid-air—or at least land with less impact force back on the rock.
Below are a few safety considerations when practicing falling on lead:
- Double-check the bolts you are going to fall on to make sure they are solid and strong. Please see our video on bolts and how to recognize bad ones.
- Makes sure to check the fall zone for obstacles or other concerns.
- Avoid falling above ledges or features in the rock that you could hit—build in a margin of safety in case your belayer gives you a too-soft or not-soft-enough catch (see next video on giving a soft catch).
- Steep or overhanging routes are typically the best for a clean fall.
- Make sure to be high enough on the climb that you will not hit the ground.
- Discuss with your belayer so they know how and when you plan to fall.
Below are a few considerations when practicing falling on lead:
- Start by taking very short falls with your waist at the bolt—or even just letting go and hanging on the rope.
- Gradually increase the distance of your falls until you are falling from the next bolt (just before clipping it).
- You can also practice pulling up rope like you are about to clip a bolt and then fall, increasing the fall distance. Be extra sure you have a clean fall zone below you and that you won’t hit the ground.
- When you start practicing falling from above the bolt, be sure your legs are not wrapped up in the rope. If your leg gets tangled or your heel caught behind the rope, it can flip you upside down. This is the scariest type of lead fall, because you could hit your head on the rock.
- When falling remember to relax. Keep your arms and legs gently bent, as if ready to pounce. Channel your best cat-like instincts for a gentle, upright landing.
- Avoid pushing out from the wall, as this will result in an arching fall that can slam you back into the rock.
- Your survival instinct might tell you to try grabbing the last quickdraw; however, if you miss, you can dangerously snag a finger in the carabiner. Practice leaving your hands free to brace yourself as you come back to the rock, or practice grabbing your knot to help make sure your rope remains in front of you as you fall.
- The greater the distance you’ve climbed above the last bolt, the less forceful the falls will be to your rope, body, and belayer. This greater distance gives the dynamic rope a chance to stretch a bit and absorb the shock.
- Avoid taking too many simultaneous falls on your rope, as the stretch and dynamic properties of the rope will be diminished temporarily (or permanently, in the case of big falls). If you’re taking a lot of falls, lower to the ground and switch ends part way through your practice session.
We hope you found this video helpful. Feel free to comment below with questions or thoughts!
Please remember, climbing is inherently dangerous. Climb at your own risk. Visit https://ClimbingTechTips.com for related comments, additional videos, and community feedback!
Since 1986, FH Machinery has been serving the fastener and forming industries with top lines of new machinery as well as good used equipment. The company has an office/warehouse just outside of Philadelphia, PA (USA) with over 30,000 square feet of space, as well as representatives in Mexico City, Mexico and Toronto, Canada, Mumbai, India to better serve the needs of its customers.
As a full-service distributor for the fastener industry, FH Machinery can also supply tooling, tool design, product development and rebuilding/remanufacturing. Through its global network of suppliers, the company has the ability to offer customers in the U.S. and around the world the very best new and used equipment available anywhere.
As a quality used equipment distributor, FH Machinery is always in the market for good used equipment, purchasing single pieces or even entire facilities.
As a quality used equipment distributor, FH Machinery is always in the market for good used equipment, purchasing single pieces or even entire facilities. Over the past decade, the company acquired a significant inventory of Fastener and Cold Forming manufacturing equipment through the purchase of complete facilities, and it has also added CNC wire forming to its product lines, to better serve customers as they diversify.