Stainless Steel Set Screws Grub Screws
Metric Size: M1.4 - M52, Inch Size: 0# - 2"
Hexagon Socket(Allen), Torx Star, Square, Slotted Drive Types
Flat Point, Cup Point, Cone Point, Dog Point
Other Drive and Point Type are also available acc. to customer requirement
Various Surface Finishes
Various Material Grades are available
Please feel free to contact us for more details
We take "customer-friendly, quality-oriented, integrative, innovative" as objectives. "Truth and honesty" is our administration ideal for Factory making China Slotted Headless/Grub/Set Screws with Flat Point M1.6-M24; 2#-5/8′′, In case you have the requirement for almost any of our products and solutions, you should contact us now. We have been looking forward to hearing from you soon. Factory making China Screw, Stopper Screw, Our solutions are produced with the best raw materials. Every moment, we constantly improve the production programme. In order to ensure better quality and service, we have now been focusing on the production process. We have got high praise by partner. We've been looking forward to establishing business relationship with you.
Call: 877-594-4729
Askew Head Bolts In Maryland From Baco Enterprises Inc.
If you’re in Maryland and you need askew head bolts for your next job, choose a supplier that can meet your needs fast.
Askew head bolts are important structural components that secure tension and provide an angled head contact area. You’ll find these bolts in a range of different applications, from electrical towers to concrete wall brackets. If you’re looking for askew head bolts that are available to ship quickly, then you must source them from the right fastener distributor. Many industrial professionals throughout the U.S. already know that Baco Enterprises Inc. is the best source for askew head bolts and so many other types of structural fasteners. We make it easy to get a quote fast and can complete delivery in as little as 24 hours.
Industrial fastener customers throughout MD trust us as their best source for askew head bolts, and we invite you to do the same.To learn more, visit our website or call us directly.
Company: BACO Enterprises Inc.
Address: 1190 Longwood Avenue
City: Bronx
State: New York
Zip: 10474
Phone: 877-594-4729
URL: https://www.bacoent.com/category/202/Askew-Head-Bolts.html
www.deltastorage.com
The installation of your new toolbox will require two people, a tape measure and a ½ inch deep socket and ratchet with an extension.
Begin with the toolbox on the ground behind the vehicle. The lid latches should face away from the truck.
Open the lid, remove the tray and check for the following:
Installation instructions
Keys
Two adhesive mounting pads
Two “J” bolts
Two metal washers
Two plastic retaining washers
Two nuts
Read the instructions prior to beginning installation.
Lift the box and place about halfway across the truck bed.
Turning the box upside-down will make re-positioning easier.
Position the mounting pad to align with the inside edge of the side wall, and approximately four inches from the front bed wall.
Press down to ensure firm, even contact of the adhesive.
Repeat for the other side.
Roll the toolbox right side up onto the mounting pads. Test that there is sufficient clearance for the lid to open.
At the front of the box, use your tape measure to ensure the gap between the inner wall of the truck bed and the inner sidewall of the toolbox are the same on each side. The box is now centered.
Lift the toolbox lid.
Locate the center mounting slot.
Next, place the retaining washer onto the “J” bolt, about ½ inch from the top.
This will keep the bolt from dropping through the mounting slot.
Slightly raise the toolbox and insert the “J” bolt into the mounting slot with the hook facing the bed wall.
Turn the bolt 90 degrees, lower the toolbox and slide the “J” bolt toward the lip of the bed wall.
Rotate the “J” bolt back to its original position and pull up.
The “J” bolt should catch on the underside of the bed wall lip.
Push down on the retaining washer to hold in place and attach the flat washer and nut.
With a ½ inch deep socket, ratchet until snug. Do not yet fully tighten.
Repeat for the other side.
Double-check all measurements to ensure the box hasn’t moved off-center during installation. Readjust if needed.
Now, firmly tighten both “J” bolts.
Place the tray back inside the box.
Retain your keys and close the lid.
The installation is complete.
www.deltastorage.com