Metric Size Socket Set Screws
Thread Size: M1.4-M52
DIN913, DIN914, DIN915, DIN916
ISO4026, ISO4027, ISO4028, ISO4029
Various Drive and Point Types
Various Surface Finishes
Other Material Grades are available
Please feel free to contact us for more details
Chuyên sản xuất: KẸP XÀ GỒ/ kẹp chữ C/ kẹp HB2/TY REN/TY TREO/TY RĂNG/THANH REN/ TY TREO mạ kẽm M6, M8, M10, M12, M16 – (High quality Galvanized Thread Rod) 1m, 2m, 3m, đạt tiêu chuẩn JIS B 1051 – JAPAN & DIN 975 & DIN 976- Đức, Đai treo /Cùm treo, Đai treo 2 mảnh (Pipe hanger/Conduit Clamp), tắc kê đạn, Đai treo Omega, cùm omega, Cùm Ubolt, Cùm Ubolt lá (U Bolts) Gía đỡ cơ điện (M&E/Mechanical Fixings, Fasteners and Spring steel Supports) Cùm treo ống / Kẹp treo ty & ống / Kẹp treo ống thép luồn dây điện, ống PCCC/ HVAC (Steel conduit hanger/Pipe hanger/Clevis Hanger), Kẹp xà gồ/ Kẹp dầm thép (Beam Clamp/Suspending Clamp/C-Clamp), Thanh chống đa năng (Unistrut Channel/ Strut/ C-Channel/ Double Unistrut profile ), Đai ốc lò xo cho thanh chống đa năng (Long spring nut), Tay đỡ đơn (Cantilever Arm), U cùm ( U bolts), Tắc kê đạn (Drop In Anchor), Đai treo (bát treo) cho hệ thống điện nhẹ M&E / HVAC/PCCC /Điều hoà không khí cho toà nhà cao tầng và nhà máy sản xuất công nghiệp tại Việt Nam.
Mọi thông tin chi tiết về sản phẩm của Cát Vạn Lợi, xin quý khách hàng vui lòng liên hệ: 1900 5555 49
CÔNG TY TNHH THIẾT BỊ ĐIỆN CÔNG NGHIỆP CÁT VẠN LỢI
VPGD : 61 Đường số 7, KDC CityLand Center Hills, P. 7, Q. Gò Vấp, TPHCM
Tel: 08-35886496/ 22 46 46 99
Fax: 08-35886505
E-mail: baogia@catvanloi.com
Website: WWW.CATVANLOI.COM –
https://ongluondaydienvietnam.wordpress.com/
Phòng chăm sóc khách hàng: 0943353039 (Mr.Tâm)
Subscribe to our channel for the latest training videos, climbing tutorials and more! Unlike gym climbing, outdoor climbing typically requires an anchor to be created at the top of the route. There are several anchor systems to choose from. In this video, we review the “Sliding X.” This is an anchor which has gone in and out of style through the years, and has some pitfalls. It is not our most recommended anchor style, but we discuss it here so that you are familiar with if, how, and when to use it.
The main benefit of the Sliding X is that it can automatically adjust the equalization point; therefore, it can be a good choice for a wandering climb, where the climber will traverse while climbing to the anchor.
2 – Pre-existing bolts and hangers
2 – Double-length slings
2 – Non-locking carabiners
AND
1 – Locking carabiner -and- 1 non-locking carabiner
OR
2 – non locking carabiners
OR
2 – locking carabiners for the Master Point
Step 1 – Clip the 2 non-locking carabiners into the bolted anchor points (one carabiner for each bolt hanger).
Step 2 – Clip two double length slings (for redundancy) into each carabiner, and pull in the direction of the climber.
Step 3 – Holding each “half” of the double length sling in one hand, which means you’ll have two strands in each hand, flip one to create a loop. This marks the X of the Sliding X.
Step 4 – Clip all four strands with two opposite and opposed carabiners. The carabiners should slide smoothly from side to side as the slings adjust the equalization point.
NOTE: At no point should the Master Point (which is less defined in this anchor, but is where the opposite and opposed carabiners rest) drop down and shock load either piece of the anchor. This is possible with the Sliding X if one of the bolts were to fail (and violates SRENE, see video). For this reason, we use two double length slings so we are very confident in the strength of the slings, and two unquestionably solid bolts.
We hope you found this video helpful. Feel free to comment below with questions or thoughts!
Please remember, climbing is inherently dangerous. Climb at your own risk. Visit https://ClimbingTechTips.com for related comments, additional videos, and community feedback!