Buy everything you see in these video’s here online Now:
Tub And Shower Faucet: https://go.magik.ly/ml/a583/
Extra cover plate: https://go.magik.ly/ml/a64f/
Moen Tub and shower cartridge: https://go.magik.ly/ml/a64a/
1/2 copper 90′s: https://go.magik.ly/ml/a64i/
1/2 Copper Streed 90′s: https://go.magik.ly/ml/a64l/
1/2 Brass wing 90: https://go.magik.ly/ml/a64o/
Gas and touch set: https://go.magik.ly/ml/a64q/
In this video we start by removing the old two handle tub and shower valve from inside the wall. First we remove the handles and spout leaving the shower head in place to hold up the old shower valve and keeping it there until the new shower valve is in place this makes it easy and keeps use inline with the new installation and makes it very easy to line up the new shower head. Now that we have the handle off its time to go around on the back side and cut into the wall or if were lucky there just may be a trap door on the back side that gives us access to the tub and shower valve from the back side. Once on the back side of the tub and shower valve we start by disconnecting the unions on the old two handle tub and shower valve. Now the part that goes up to the shower head is copper. What we are going to do here is take our torch and heat the solder connection and pull the valve loose from the shower head riser pipe. Now with the old tub and shower valve out the way lets go back to the front side in the bath room. Now this was a three handle tub and shower valve so were going to have to make some adjustments to the hole in the wall in this case we will have to open the middle hole a little wider for the new single handle tub and shower valve. This is not your standard drywall (sheetrock) wall this is old and very thick no cutting this with a saw saw. What were going to do here is use a hammer and just lightly knock out pieces of the wall slow and easy. Don’t worry about covering up the old holes they make a cover plate for that. We have the hole just how we won’t it lets go back to the other side behind the tub and shower. What I like to do is put my new tub and shower valve to gather and solder pieces in place before I start working in the wall with it and I also remove the washers in the valve so we don’t damage the washers with the hot torch and burn them up once all this is done I take the tub and shower valve and put it into place line it up and make all the necessary connections from the back side from here I go back to the front of the valve in that bath room and start putting all the trim on but installing the cover plate first then if you like caulk it. Thank you for watching coolplumbingvideos.
-~-~~-~~~-~~-~-
Please watch: “Pex Pipe Plumbing (The Complete Series)
2013 Toyota Avalon Review: Used Cars Tips – 2013 Toyota Avalon
2013 Toyota Avalon Review & Test-Drive by The Car Pro, Jerry Reynolds, Car Pro Show, https://vimeo.com/carproshow, https://vimeo.com/61142196
New Avalon – is the result of North American research and engineering efforts in the design of the car. Appearance sedan and interior design have been developed talented team Calty Design Research Inc. in South-ern California and Michigan. Engineering made dedicated group of Toyota Technical Center in Ann Arbor. The car itself is assembled in Georgetown, Kentucky.
Improved dynamics Avalon
In addition to its stunning design, numerous changes to improve the ride quality, and management has undergone. The body structure further im-proved due to the high strength steel and the seams in key areas in or-der to provide a more rigid chassis and optimize the suspension. The new suspension Avalon relies on MacPherson struts with control springs to balance handling and agility.
The new Avalon offers three different modes that help tailor dynamic performance to the needs of the driver. Modes – Normal, Eco and Sport switch selectable. In Eco mode lowers power consumption and improves fuel economy.
The dynamic exterior design
The dynamic exterior design of the new Avalon is defined by its sleek and expressive profile through which you can admire the car even if it is at rest. Compared with its predecessor, the new Avalon a little more com-pact. New 17-inch and 18-inch alloy wheels and tires complement the dynamic expression of the vehicle.
The main elements of the exterior design include: Double-eye PES (Pro-jector Ellipsoid System), headlamps with HID (High-Intensity Discharge) and elegant DRL (Daytime Running Lights), which obespeivayut excellent visibility at night, helping to identify dangerous road sections. The rear panel LED lamp high. Dual rear exhaust pipes ensure the integrity of the design.
Security
As with all models of Toyota, the new Avalon has a feature Toyota’s Star Safety System, which includes: Vehicle Stability Control (VSC), Traction Control (TRAC), Anti-lock braking system (ABS), Electronic Brake-force Distribution (EBD), Brake Assist , and Smart Stop Technology brake-override system.
In addition to the rear-view monitor, Avalon offers a monitoring system that helps detect vehicles outside the view of the driver and mirrors.
For consumers looking for a mid-size sedan with excellent fuel economy and high environmental ratings, the new Avalon offers a complete hy-brid-split system. In conjunction with the reduction of vehicle weight and improved aerodynamics, Avalon Hybrid achieves impressive fuel economy ratings. In 2013, Avalon includes the latest advances in technology Toyo-ta Hybrid Synergy Drive, developed by the company for 14 years. Avalon Hybrid has a 2.5-liter, four-cylinder engine, 244.8-volt nickel-metal hy-dride battery and a pair of electric motors.
Avalon Hybrid achieves a total system power of 200 horsepower and of-fers three unique modes of operation: EV, ECO and SPORT. Avalon Hy-brid models consume 1 gallon to 40 miles in the city and 1 gallon per 40 miles on the highway.
Toyota Corolla 2010 LE Super White