Follow me on Instagram: www.instagram.com/cars.y.life
In this episode, the measuring tools needed to measure the piston to cylinder clearance are introduced. The measurements required to compute the clearance are reviewed.
|MY MODS|
ENGINE
- BOSS 5.0 cast iron block
- Manley Pro Series I-beam rods
- Manley forged pistons (with MMR coating)
- MMR 4.75 stroker crank forged 4340
- MMR/Ford Racing Stage 3 ported heads
- MMR/Comp Stage 3 turbo cams
- Livernois cam phaser lockouts
- Ford Racing 3V air intake manifold (carbon hydro-dipped)
- APR 2000 head studs, rod bolts, side bolts, main cap studs
- Ford Racing twin 62 mm throttle body
- C&L 95 mm cold air intake
- MMR billet oil pump gears
- MMR 7 quart oil pan (red)
- Moroso welded aluminum valve covers
- Powder coated timing cover (black)
- MSD Blaster Coils
- Steeda aluminum belt tensioner
- Romac Pro Harmonic Balancer
TRANSMISSION/DRIVELINE
- Tremec T-56 Magnum XL 6-speed (Ford Racing packaged)
- SFI certified bell housing
- McLeod RXT 1200 twin-disk clutch
- McLeod aluminum 8-bolt flywheel with steel insert
- APR 2000 flywheel bolts
- JPC clutch line upgrade
- Driveshaft shop one-piece aluminum driveshaft (for T-56 transmission)
WHEELS/TIRES
- Wheels: Forgestar CF5V 19” diameter x 12” wide with 6 mm offset wheels (all four corners)
- Front tires: Continental Extreme Contact P305/30ZR19 (102Y)
- Rear tires: Kumho Ecsta V720 ACR P355/30ZR19 (99Y)
- McGard black lug nuts with locks
ENGINE BAY
- Trufiber carbon fiber full-length radiator cover
- Moroso welded aluminum radiator expansion tank
- Moroso welded aluminum power steering tank
- Ford Racing Boss 302 style strut tower brace (carbon dipped)
EXTERIOR
- Trufiber widebody fender flares
- Trufiber carbon fiber decklid panel
- Raxiom smoked projector lights (GEN 5 style)
- Raxiom smoked vector tail lights with white diffusers (GEN 6)
- CDC chin spoiler (carbon fiber wrapped)
- CDC chin splitter (carbon fiber wrapped)
- MMD ducktail spoiler (carbon fiber wrapped)
- SVE Bullet style grill
- Trufiber 3 inch cowl hood
- Custom painted hood, roof, trunk
- MGP red brake caliper covers
INTERIOR
- Brushed aluminum interior kit
- Autometer Nexus boost, fuel pressure, A/F ratio gauges
- Autometer Nexus trans. temp, oil temp, exhaust temp gauges
- Speed of Sound A-pillar gauge pod
- Speed of Sound dash gauge pod
FUEL
- Kenne Bell boost-a-pump
- Ford Racing 47 lb/hr injectors
COOLING
- Mishimoto performance radiator
- Ford Racing performance radiator fan
- Mishimoto 170 F thermostat
- Mishimoto silicon hose kit (black)
CHASSIS/SUSPENSION
- Eibach Pro suspension kit (with sportline springs in front)
- BMR tubular K-member
- BMR tubular front lower control arms (A-arms)
- BMR adjustable rear upper control arm
- BMR upper control arm mount
- BMR adjustable rear lower control arms (spherical & poly)
- BMR lower control arm relocation brackets
- J&M adjustable panhard bar
EXHAUST
- BBK tuned length shorty headers
- BBK 2.75 inch X-pipe (catted and off-road, can switch)
- MBRP 3 inch catback exhaust
TUNING
- Custom tune from Chris Groves @ The Dyno Edge
PLANNED FUTURE MODS
- Turbohorsepower twin turbo kit
- Boost controller
- Injector Dynamics 1300 fuel injectors
- 1000+ hp return style fuel system (not sure which brand yet)
- Stronger axles
- New differential & gears
- APR Performance carbon fiber diffuser
- APR Performance carbon fiber side skirts
- APR Performance carbon fiber rear lip splitters
In this video, the Idahoan demonstrates an inexpensive process for making custom grips to improve the ergonomics of a revolver.
DISCLAIMER: Careless or improper use of tools can lead to serious injury. Careless or inept attempts to assemble/disassemble firearms can damage said firearms. Careless handling of firearms can lead to injury or death. Your safety is YOUR responsibility. Do not attempt to reproduce anything shown in this video unless you can do so safely.